A Step-by-Step Guide to Setting Up a Bathtub
A Step-by-Step Guide to Setting Up a Bathtub
Blog Article
We've unearthed this great article on A Step-by-Step Guide to Installing a Bathtub down the page on the net and decided it made perfect sense to discuss it with you on this page.
Setting up a bath tub isn't exactly rocket science, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately challenging project. If the old bathtub is easily accessible, the task can move speedily; if you need to open a wall surface to eliminate the old tub and also position the new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually qualified on your own for the task and also are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed task, it is far better to consider using one before you start. Chances are you might need a specialist plumber to make tube connections.
This short article will certainly help you mount a brand-new bathtub in your washroom if you have currently bought a brand-new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your devices and material list should make up the following:
Getting ready for the Installment
First of all, the supporting structure supplied with the bath must be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop stress on the tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the supply of water and also check all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and also the regular outlet for leaks.
Lastly, fix the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait until the tub has been made use of at the very least when as this will certainly settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are offered in tubes as well as cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads about How to Install a Bathtub, I figured sharing that excerpt was a smart idea. Feel free to set aside a second to share this article if you enjoyed reading it. Kudos for your time. Please stop by our site back soon.
Get A Quote
Report this page